Services
Contractor & Small-Business Fabrication
Jobsite carts, material stands and equipment mounts for crews that work from a truck or trailer.
Custom fabrication in the shop or on site, by appointment.
Gear gets knocked around on the way to the site
A crew that works from a truck or trailer loses time to gear that is never where it should be. Bins slide across the bed on the first turn, a material stand lands against a fender, and a pry bar ends up under the pallet jack. Much of that damage and lost time happens on the drive between jobs, not on the job itself.
We build for the way gear actually moves. We look at what goes on the truck, how it gets loaded, and what it has to survive on a rough road. From there we design carts, stands and bins that hold their place when the vehicle stops, and still come off the bed quickly at the other end.
The truck bed has no good place for a stand or cart
Most work trucks and trailers come with an open bed and a few tie-down points. That works until you need a stand for a cut-off saw, a cart for a bag of fittings, or a bracket that keeps a jack from sliding. Without a planned place for each piece, the bed fills up with whatever is closest, and every job starts with a rearrangement.
We fit fixtures to the vehicle you run. Before any metal is cut, we look at the bed or deck layout, the height and width you have to work with, and where each piece has to be reached from. If a stand would block a tailgate or a ramp, we will say so before the design is final.
Mounts and bins that hold up on a rough site
Jobsite gear takes abuse. Dirt, water, dropped tools and daily loading wear down anything built as an afterthought. A mount that works fine in the yard can loosen after a month of bouncing down a gravel drive, and a bin with a weak corner splits the first time someone stands on it.
We keep designs plain and use proven materials sized for the load each piece carries. We check how every part is fixed to the truck or trailer, because a sound stand on a weak mount still fails. Where a design has a real limit, such as a maximum load for a bin or a weight a stand should not take, we write that down so the crew knows it too.
Example Builds
- Jobsite carts for bins, fittings and hand tools
- Material stands for pipe, lumber and sheet goods
- Equipment mounts for saws, trimmers and blowers on a truck or trailer
- Bin racks and tool holders bolted to the bed or trailer deck
- Stands that hold portable equipment at a steady working height
- Brackets and organizers for jacks, chains, straps and hand tools

What to Send Us
- Side and overhead shots of the truck bed or trailer deck, with the gear in place
- A list of each tool, bin or piece of equipment, with rough sizes and weights
- Where each cart, stand or mount has to sit, and any limits such as ramps, racks or tailgate swing
- How often each piece is loaded, unloaded and used on site
- The year, make and model of the truck or trailer, where known
What We Don't Take On
Some contractor gear goes beyond carts, stands and mounts. We don't take on load-rated lifting attachments, such as hoist hooks or lift arms that must be rated and tested before they lift anything. We don't build structural work for buildings, frames or load paths, and we don't build anything that carries people, such as platforms, seats, ladders or work positions. Those need engineering, ratings and approvals before anyone builds them, so that work is outside what we do here.
Questions
What kinds of contractor gear do you build?
Carts, material stands, bin racks, tool holders and equipment mounts for trucks, trailers and job sites. If you are not sure an idea fits, send photos and the gear list, and we will say whether it is a good match.
Do you build for a truck or trailer I already own?
Yes. Most of this work is fitted to the vehicle you already run. We work from photos and measurements of the bed or deck, and we note any clearance limits before the design is final.
Can you build a stand for one specific piece of equipment?
Usually. Send the equipment size and weight, and describe how it gets moved on and off the truck. We will say what the stand would look like and whether it will hold up to daily use.
Do you build carts that stay in my shop?
Carts and benches that stay in a workshop are covered on the Shop Fabrication page. This page is for gear that goes to the job, such as jobsite carts, material stands and equipment mounts.
Can we get a piece built on a tight deadline?
Rush work is not something we normally take. Each project is booked in advance, and the date depends on the design and on what is already on the calendar. Ask when you call, and we will give you a straight answer.
By Appointment
Have a Project in Mind?
Describe the problem, send photos and approximate dimensions, and we'll let you know if it's a fit.
